Sound System Accessories
You may want amplifiers for extra low or extra high voltage, snubber diodes for switched outputs or extra cables to round out your Sound System. Everything you need to complete your sound system is here.
What's New:
SFX7.0 Sound Module
February, 2012
SFX7 now being manufactured!
SFX7.0 Sound Module
January, 2012
The NEW SFX7 heralds another world first with the first and only stereo capable R/C sound Module. Its 1GB microSD Card makes changing sound sets a breeze. It is also completely setup free.
Sound System Accessories
|
Pre-Loaded Micro-SD Card for SFX7 |
||||
 |
Item Name : PRE-LOADED MICROSD CARD
FOR SFX7 |
|||
|
These microSD Cards are supplied by us pre-loaded with up to four .sfx5 sound sets of your choice and compatible hardware settings files. You can simply swap in a new microSD Card for the existing one in a SFX7 sound module and have a completely different set of sounds. Each microSD Card also includes the latest firmware and PC software releases and documentation suite. The card comes in a small plastic case. Note: These microSD cards have been carefully tested by us to meet all performance requirements of the SFX7 sound module. Be wary of other sources of cheap microSD Cards - they may not work in the SFX7 sound module. It is highly recommended that you backup all the files on the SFX7 microSD card as soon as you receive it. |
||||
|
|
||||
| 5-15 Volt Audio Amplifier | ||||
|
Item Name : LOW VOLTAGE AUDIO
AMPLIFIER Price is in Canadian $$ - See XE.Com Currency Converter |
||||
|
This low voltage amplifier, with
a supply voltage range of 5-15Volts, is suitable for 6V, 7.2V
and 9.6V models that use our SFX6.4 sound module. It is
recommended to use a |
||||
|
|
||||
| 22 AWG Hook-Up Wire for Loudspeakers and Sound Module Power | ||||
 |
Item Name: 22AWG Hook-Up Wire Price is in Canadian $$ - See XE.Com Currency Converter Please adjust the quantity in your shopping cart to show the correct number of feet of wire for all colours you want. Please indicate which length of which colour in the "Notes to Seller" section of the checkout page. |
|||
|
We recommend using this 22AWG solid cored hook-up wire to connect your loudspeaker(s) and battery supply to the SFX7 sound module. Available in red/black (for battery supply or for two loudspeakers) and green (usually for a single loudspeaker). Since two 4Ohm loudspeakers must be wired in series with each other, it is a good idea to use black/red wire for this as it is important to have them wired in phase. |
||||
|
|
||||
| SPST Slide Switch | ||||
|
Product may not be |
Item Name: SPST Slide Switch Price is in Canadian $$ - See XE.Com Currency Converter |
|||
|
This full size slide switch can be used used to switch the power to your sound module or other accessories in your model. |
||||
|
|
||||
| 3Amp Fast Acting Fuse | ||||
|
|
Item Name: 3 Amp Fast Acting Fuse Price is in Canadian $$ - See XE.Com Currency Converter |
|||
|
We recommend adding a 3 Amp in-line fuse in the positive power supply to our sound modules. This is to protect your wiring should there be accidental short circuits or a reversed battery. Note: A fuse will not act fast enough to protect the sound module if you reverse the battery, but it will save your wiring and possibly other components from smoking! |
||||
|
|
||||
| In-Line Fuse Holder | ||||
|
Product may not be |
Item Name: In-Line 1/4" x 1 1/4" Fuse Holder Price is in Canadian $$ - See XE.Com Currency Converter |
|||
| This in-line fuse holder will hold the recommended 1/4" x 1 1/4" fuses above. | ||||
|
|
||||
Snubber Diodes for Switched Outputs |
||||
|
|
Item Name: Snubber Diode - 50V - 1A
Price is in Canadian $$ -
See
XE.Com Currency Converter |
|||
|
LED flasher and switched outputs
on our SFX6.4 sound modules are designed to switch LEDs or
lamps, not inductive loads. If you wish to switch any inductive
load such as a relay, small motor, solenoid etc., you MUST
connect a "snubber" device across the load to prevent reverse
inductive kickback voltages from damaging the sound module. |
||||
|
|
||||
Male - Male Servo Cable |
||||
 |
Item Name : Male-Male servo
cable - 300mm (12in) long Price is in Canadian $$ -
See
XE.Com Currency Converter |
|||
|
This male-male servo cable with
Futaba style connectors on each end is 300mm long and uses 24AWG
stranded wire. It is used to connect R/C receiver throttle and
sound select outputs to our SFX6.4 sound module. The SFX6.4
sound module includes two of these cables - one for a Throttle
input and one for a Sound Select Input. This is the usual
configuration. |
||||
|
|
||||
Screened Audio Cable - 150mm |
||||
 |
Item Name : Audio cable -
150mm (6") long |
|||
|
This audio cable has Futaba style male connectors on each end and is used to connect the Audio out of a SFX6.4 module to an external amplifier for either lower voltage or higher power. |
||||
|
|
||||
USB Cable |
||||
 |
Item Name : Mini-B USB cable,
1 meter long |
|||
|
The SFX6.4 sound module has a
mini-B USB connector which is the same type found on many
digital still and video cameras. This high quality USB cable is
offered for those users who do not already have such a cable.
This is an industry standard USB cable with a male mini-B
connector on one end and a male type A USB connector on the
other. |
||||
|
|
||||
The World's Most Advanced R/C Sound Systems
